Experimental test of multi-stage vertical-axis turbines for cellular communication applications

John Abraham, Brian Plourde, Greg Mowry, Ephraim Sparrow

Research output: Chapter in Book/Report/Conference proceedingConference contribution

Abstract

A multi-year research program has generated a working prototype for a vertical-axis wind turbine that is capable of powering cellular communication equipment. The turbine is designed to be affixed to already existing communication towers and thereby has a reduced cost of installation. The turbine is driven by air drag forces rather than by lift. It has a number of novel features including venting slots that are created to reduce the thrust loading on the communication tower. In addition, contoured caps are affixed to the upper and lower edges of the turbine blades to increase power production. As previously mentioned, the turbine design itself is a drag-based concept rather than the more typical lift-driven devices. The advantages of the drag-based design are: 1. lower startup wind speed, 2. slower rotation and a lessened vibrational load on the tower, 3. less sensitive to wind direction, and 4. it can be aligned with the tower. The design of the device was carried out through a combination of numerical simulation and experimentation. The simulations have evolved from preliminary two-dimensional calculations to a fully three dimensional, unsteady, computational fluid dynamic analysis. Simultaneously, the experiments have included both in-field and wind-tunnel tests of various stages of the turbine design. An outcome of the effort is a third-generation working vertical-axis wind turbine (VAWT) that is currently being evaluated with in-field tests. The results of the tests are positive and confirm the expectations that were developed during the product design phase. The turbine, which can be constructed with various rotor stages, has the capability of producing approximately 2-3 kW of power in wind-speed environments of 12-16 m/s. These power production levels are greatly in excess of that required to fully power the electronics equipment on a typical cellular communication tower. Unfortunately, subsequent tests showed that the turbine production dropped approximately sevenfold. The cause of the decrease in performance was friction in the mechanical components which coupled the rotating shaft to the support structure. This recognition reinforces the importance of low-resistance mechanical design for VAWTs. Another aspect of the turbine design is the specialized electronics which allow the electronics to adapt to local wind speeds and consequently increase the efficiency of the power production.

Original languageEnglish (US)
Title of host publicationASME 2012 6th International Conference on Energy Sustainability, ES 2012, Collocated with the ASME 2012 10th International Conference on Fuel Cell Science, Engineering and Technology
PublisherAmerican Society of Mechanical Engineers
Pages1333-1339
Number of pages7
EditionPARTS A AND B
DOIs
StatePublished - Jan 1 2012
EventASME 2012 6th International Conference on Energy Sustainability, ES 2012, Collocated with the ASME 2012 10th International Conference on Fuel Cell Science, Engineering and Technology - San Diego, CA, United States
Duration: Jul 23 2012Jul 26 2012

Other

OtherASME 2012 6th International Conference on Energy Sustainability, ES 2012, Collocated with the ASME 2012 10th International Conference on Fuel Cell Science, Engineering and Technology
CountryUnited States
CitySan Diego, CA
Period7/23/127/26/12

Fingerprint

Cellular radio systems
Turbines
Towers
Drag
Electronic equipment
Wind turbines
Communication
Product design
Dynamic analysis
Turbomachine blades
Wind tunnels
Computational fluid dynamics
Rotors
Friction
Computer simulation
Air

Cite this

Abraham, J., Plourde, B., Mowry, G., & Sparrow, E. (2012). Experimental test of multi-stage vertical-axis turbines for cellular communication applications. In ASME 2012 6th International Conference on Energy Sustainability, ES 2012, Collocated with the ASME 2012 10th International Conference on Fuel Cell Science, Engineering and Technology (PARTS A AND B ed., pp. 1333-1339). American Society of Mechanical Engineers. https://doi.org/10.1115/ES2012-91025

Experimental test of multi-stage vertical-axis turbines for cellular communication applications. / Abraham, John; Plourde, Brian; Mowry, Greg; Sparrow, Ephraim.

ASME 2012 6th International Conference on Energy Sustainability, ES 2012, Collocated with the ASME 2012 10th International Conference on Fuel Cell Science, Engineering and Technology. PARTS A AND B. ed. American Society of Mechanical Engineers, 2012. p. 1333-1339.

Research output: Chapter in Book/Report/Conference proceedingConference contribution

Abraham, J, Plourde, B, Mowry, G & Sparrow, E 2012, Experimental test of multi-stage vertical-axis turbines for cellular communication applications. in ASME 2012 6th International Conference on Energy Sustainability, ES 2012, Collocated with the ASME 2012 10th International Conference on Fuel Cell Science, Engineering and Technology. PARTS A AND B edn, American Society of Mechanical Engineers, pp. 1333-1339, ASME 2012 6th International Conference on Energy Sustainability, ES 2012, Collocated with the ASME 2012 10th International Conference on Fuel Cell Science, Engineering and Technology, San Diego, CA, United States, 7/23/12. https://doi.org/10.1115/ES2012-91025
Abraham J, Plourde B, Mowry G, Sparrow E. Experimental test of multi-stage vertical-axis turbines for cellular communication applications. In ASME 2012 6th International Conference on Energy Sustainability, ES 2012, Collocated with the ASME 2012 10th International Conference on Fuel Cell Science, Engineering and Technology. PARTS A AND B ed. American Society of Mechanical Engineers. 2012. p. 1333-1339 https://doi.org/10.1115/ES2012-91025
Abraham, John ; Plourde, Brian ; Mowry, Greg ; Sparrow, Ephraim. / Experimental test of multi-stage vertical-axis turbines for cellular communication applications. ASME 2012 6th International Conference on Energy Sustainability, ES 2012, Collocated with the ASME 2012 10th International Conference on Fuel Cell Science, Engineering and Technology. PARTS A AND B. ed. American Society of Mechanical Engineers, 2012. pp. 1333-1339
@inproceedings{427ae38ac6704fe993a6cbd2f87d77c3,
title = "Experimental test of multi-stage vertical-axis turbines for cellular communication applications",
abstract = "A multi-year research program has generated a working prototype for a vertical-axis wind turbine that is capable of powering cellular communication equipment. The turbine is designed to be affixed to already existing communication towers and thereby has a reduced cost of installation. The turbine is driven by air drag forces rather than by lift. It has a number of novel features including venting slots that are created to reduce the thrust loading on the communication tower. In addition, contoured caps are affixed to the upper and lower edges of the turbine blades to increase power production. As previously mentioned, the turbine design itself is a drag-based concept rather than the more typical lift-driven devices. The advantages of the drag-based design are: 1. lower startup wind speed, 2. slower rotation and a lessened vibrational load on the tower, 3. less sensitive to wind direction, and 4. it can be aligned with the tower. The design of the device was carried out through a combination of numerical simulation and experimentation. The simulations have evolved from preliminary two-dimensional calculations to a fully three dimensional, unsteady, computational fluid dynamic analysis. Simultaneously, the experiments have included both in-field and wind-tunnel tests of various stages of the turbine design. An outcome of the effort is a third-generation working vertical-axis wind turbine (VAWT) that is currently being evaluated with in-field tests. The results of the tests are positive and confirm the expectations that were developed during the product design phase. The turbine, which can be constructed with various rotor stages, has the capability of producing approximately 2-3 kW of power in wind-speed environments of 12-16 m/s. These power production levels are greatly in excess of that required to fully power the electronics equipment on a typical cellular communication tower. Unfortunately, subsequent tests showed that the turbine production dropped approximately sevenfold. The cause of the decrease in performance was friction in the mechanical components which coupled the rotating shaft to the support structure. This recognition reinforces the importance of low-resistance mechanical design for VAWTs. Another aspect of the turbine design is the specialized electronics which allow the electronics to adapt to local wind speeds and consequently increase the efficiency of the power production.",
author = "John Abraham and Brian Plourde and Greg Mowry and Ephraim Sparrow",
year = "2012",
month = "1",
day = "1",
doi = "10.1115/ES2012-91025",
language = "English (US)",
pages = "1333--1339",
booktitle = "ASME 2012 6th International Conference on Energy Sustainability, ES 2012, Collocated with the ASME 2012 10th International Conference on Fuel Cell Science, Engineering and Technology",
publisher = "American Society of Mechanical Engineers",
edition = "PARTS A AND B",

}

TY - GEN

T1 - Experimental test of multi-stage vertical-axis turbines for cellular communication applications

AU - Abraham, John

AU - Plourde, Brian

AU - Mowry, Greg

AU - Sparrow, Ephraim

PY - 2012/1/1

Y1 - 2012/1/1

N2 - A multi-year research program has generated a working prototype for a vertical-axis wind turbine that is capable of powering cellular communication equipment. The turbine is designed to be affixed to already existing communication towers and thereby has a reduced cost of installation. The turbine is driven by air drag forces rather than by lift. It has a number of novel features including venting slots that are created to reduce the thrust loading on the communication tower. In addition, contoured caps are affixed to the upper and lower edges of the turbine blades to increase power production. As previously mentioned, the turbine design itself is a drag-based concept rather than the more typical lift-driven devices. The advantages of the drag-based design are: 1. lower startup wind speed, 2. slower rotation and a lessened vibrational load on the tower, 3. less sensitive to wind direction, and 4. it can be aligned with the tower. The design of the device was carried out through a combination of numerical simulation and experimentation. The simulations have evolved from preliminary two-dimensional calculations to a fully three dimensional, unsteady, computational fluid dynamic analysis. Simultaneously, the experiments have included both in-field and wind-tunnel tests of various stages of the turbine design. An outcome of the effort is a third-generation working vertical-axis wind turbine (VAWT) that is currently being evaluated with in-field tests. The results of the tests are positive and confirm the expectations that were developed during the product design phase. The turbine, which can be constructed with various rotor stages, has the capability of producing approximately 2-3 kW of power in wind-speed environments of 12-16 m/s. These power production levels are greatly in excess of that required to fully power the electronics equipment on a typical cellular communication tower. Unfortunately, subsequent tests showed that the turbine production dropped approximately sevenfold. The cause of the decrease in performance was friction in the mechanical components which coupled the rotating shaft to the support structure. This recognition reinforces the importance of low-resistance mechanical design for VAWTs. Another aspect of the turbine design is the specialized electronics which allow the electronics to adapt to local wind speeds and consequently increase the efficiency of the power production.

AB - A multi-year research program has generated a working prototype for a vertical-axis wind turbine that is capable of powering cellular communication equipment. The turbine is designed to be affixed to already existing communication towers and thereby has a reduced cost of installation. The turbine is driven by air drag forces rather than by lift. It has a number of novel features including venting slots that are created to reduce the thrust loading on the communication tower. In addition, contoured caps are affixed to the upper and lower edges of the turbine blades to increase power production. As previously mentioned, the turbine design itself is a drag-based concept rather than the more typical lift-driven devices. The advantages of the drag-based design are: 1. lower startup wind speed, 2. slower rotation and a lessened vibrational load on the tower, 3. less sensitive to wind direction, and 4. it can be aligned with the tower. The design of the device was carried out through a combination of numerical simulation and experimentation. The simulations have evolved from preliminary two-dimensional calculations to a fully three dimensional, unsteady, computational fluid dynamic analysis. Simultaneously, the experiments have included both in-field and wind-tunnel tests of various stages of the turbine design. An outcome of the effort is a third-generation working vertical-axis wind turbine (VAWT) that is currently being evaluated with in-field tests. The results of the tests are positive and confirm the expectations that were developed during the product design phase. The turbine, which can be constructed with various rotor stages, has the capability of producing approximately 2-3 kW of power in wind-speed environments of 12-16 m/s. These power production levels are greatly in excess of that required to fully power the electronics equipment on a typical cellular communication tower. Unfortunately, subsequent tests showed that the turbine production dropped approximately sevenfold. The cause of the decrease in performance was friction in the mechanical components which coupled the rotating shaft to the support structure. This recognition reinforces the importance of low-resistance mechanical design for VAWTs. Another aspect of the turbine design is the specialized electronics which allow the electronics to adapt to local wind speeds and consequently increase the efficiency of the power production.

UR - http://www.scopus.com/inward/record.url?scp=84900434731&partnerID=8YFLogxK

UR - http://www.scopus.com/inward/citedby.url?scp=84900434731&partnerID=8YFLogxK

U2 - 10.1115/ES2012-91025

DO - 10.1115/ES2012-91025

M3 - Conference contribution

SP - 1333

EP - 1339

BT - ASME 2012 6th International Conference on Energy Sustainability, ES 2012, Collocated with the ASME 2012 10th International Conference on Fuel Cell Science, Engineering and Technology

PB - American Society of Mechanical Engineers

ER -